CF232 & CF232-5V
 The CF232 is a tiny TypeI format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters).
CF232
or
CF232-5V
The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment. For more information about Linux support please click here !
Technical Features:
16C550 UART with 16-byte TX and RX FIFOs for high speed and reliable communications.
Hardware switchable baud rate multiplier allows either industry standard rates up to 115KBaud in x1 mode or up to 921Kbaud in x8 mode...no special drivers needed so faster rates work in Ce & PocketPC.
Supports 5/6/7/8 data bits, odd/even/no parity, 1/1.5/2 stop bits, baud rates including 2400, 4800, 9600, 19200, 57600, 115200 in x1 mode, and 8 times these rates in x8 mode i.e. up to 921600 baud.
Supported by standard drivers in DOS*, Windows95, 98, 98SE, Me, NT4, 2000, XP, Ce, PocketPC & Linux.
For more information about Linux support please click here !
Card comes with Elan's Card Center Pro software that installs INF scripts and sample code Automatic O.S. recognition and configuration.
Hot swappable CF+ compliant TypeI design.
Low power consumption: Typical 20mA at 5V, with support for reduced power sleep mode (depends on O.S.).
Will also work at 3.3V with true RS232 levels for hosts that cannot supply 5V.
Power consumption drops automatically when terminal equipment is not connected i.e. unplugging cable at either end.
15KVolt ESD protected RS232 drivers and receivers for protection of your card and PC.
Supplied with 300mm Type46 cable.
Connector latches into CF Card for security. DB9 Male with female screwlocks and industry standard RS232 pinout for direct attachment of terminal equipment.
Also available with robust direct cable termination instead of Type46 cable, product code CF232R. MOQ may apply.
5V Output Option:
Available as CF232-5V with Vcc output on Pin9 (instead of RI signal).
Can be used to power external equipment (with appropriate connections).
*DOS support requires Card and Socket services, e.g. CardWare from APSoft see http://www.tssc.de
_________________________________________________________________
CF232-R - ruggedized !
 The CF232-R series is a ruggedized tiny TypeI format Compact Flash (CF+) single RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop. Instead of the picture the cable is non-removable ruggedized connected with the CF card. The R15 version is equiped with an 1.5m long cable.
CF232-R
CF232-5/R
CF232-5/R15
The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment. For more information about Linux support please click here !
Technical Features:
16C550 UART with 16-byte TX and RX FIFOs for high speed and reliable communications.
Hardware switchable baud rate multiplier allows either industry standard rates up to 115KBaud in x1 mode or up to 921Kbaud in x8 mode...no special drivers needed so faster rates work in Ce & PocketPC.
Supports 5/6/7/8 data bits, odd/even/no parity, 1/1.5/2 stop bits, baud rates including 2400, 4800, 9600, 19200, 57600, 115200 in x1 mode, and 8 times these rates in x8 mode i.e. up to 921600 baud.
Supported by standard drivers in DOS*, Windows95, 98, 98SE, Me, NT4, 2000, XP, Ce, PocketPC & Linux.
For more information about Linux support please click here !
Card comes with Elan's Card Center Pro software that installs INF scripts and sample code Automatic O.S. recognition and configuration.
Hot swappable CF+ compliant TypeI design.
Low power consumption: Typical 20mA at 5V, with support for reduced power sleep mode (depends on O.S.).
Will also work at 3.3V with true RS232 levels for hosts that cannot supply 5V.
Power consumption drops automatically when terminal equipment is not connected i.e. unplugging cable at either end.
15KVolt ESD protected RS232 drivers and receivers for protection of your card and PC.
DB9 Male with female screwlocks and industry standard RS232 pinout for direct attachment of terminal equipment.
5V Output Option:
Available as CF232-5R/5R15 with Vcc output on Pin9 (instead of RI signal).
Can be used to power external equipment (with appropriate connections).
CF232-R equiped with ruggedized Type 410 non-removable cable.
CF232-R15 equiped with ruggedized Type 411 (1.5m) non-removable cable.
CF232-5R equiped with ruggedized Type 410 non-removable cable, incuding Power Ouput (3.3V or 5V) on Pin 9.
CF232-5R15 equiped with ruggedized Type 411 (1.5m) non-removable cable, incuding Power Ouput (3.3V or 5V) on Pin 9.
*DOS support requires Card and Socket services, e.g. CardWare from APSoft see http://www.tssc.de
_________________________________________________________________
CF332
 The CF332 is a TypeII format Compact Flash (CF+) dual Isolated RS232 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters).
CF332
The card automatically configures to become two COM ports by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment. The serial ports feature TX, RX, CTS and RTS signals on each port, and are isolated up to 50V DC from the host supply. The isolation feature makes it easy to avoid ground loops and offset voltages that are common in instrumentation systems, especially where long cable lengths are used to connect the RS232 equipment. Normally these offset voltages would cause unreliable comms or in some cases, no communication at all. The two COM ports share a common ground connection.
*Due to the internal isolation, and the partial RS232 interface, this card may not be suitable for connection to equipment that scavenges powers from the RS232 signal lines. Please consult us if you are unsure about a particular application.
Technical Features:
16C550 UARTs with 16-byte TX and RX FIFOs for high speed and reliable communications up to 115.2KBaud.
Uses two of Elan's unique VPU16551 highly integrated UARTs.
Each port has its own TX, RX, CTS and RTS signals, plus a common ISOGND.
ISOGND can be up to +/-50V offset from host 0V, at DC to 60Hz, whist maintaining normal operation.
Supported by standard drivers in Windows95, 98, 98SE, Me, 2000, XP, Ce, PocketPC & Linux. Card comes with Elan's Card Center Pro software that installs INF scripts and sample code.
Automatic O.S. recognition and configuration.
Hot swappable CF+ compliant TypeII design.
Low power consumption: Typical 35mA at 3.3V
Provides true RS232 levels on any PDA or laptop.
Also available with robust direct cable termination instead of Type49 cable, product code CF332R. MOQ may apply.
15KVolt ESD protected RS232 drivers and receivers for protection of your card and PC.
Supplied with 300mm Type49 cable. Connector latches into CF Card for security. DB9 Male with female screwlocks and industry standard RS232 pinout for direct attachment of terminal equipment.
_________________________________________________________________
CF428
 The CF428 is a tiny TypeI format Compact Flash (CF+) single RS422/485 asynchronous serial port for your PDA, laptop (with an optional adapter), or desktop (using one of Elan's Desktop PCMCIA adapters).
The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment. For more information about Linux support please click here !
Technical Features:
16C550 UART with 16-byte TX and RX FIFOs for high speed and reliable communications.
Hardware switchable baud rate multiplier allows either industry standard rates up to 115KBaud in x1 mode or up to 921Kbaud in x8 mode...no special drivers needed so faster rates work in Ce & PocketPC.
RS422 mode with differential TX, RX, CTS and RTS signals.
TX driver automatically tri-states when not transmitting to allow RS485 half duplex mode with a simple interconnection between TX and RX at the DB9 connector.
Half duplex mode will always see local TX data echo Built in fail-safe circuitry.
Optional internal terminating resistors available (MOQ may apply, contact Elan)
Supports 5/6/7/8 data bits, odd/even/no parity, 1/1.5/2 stop bits, baud rates including 2400, 4800, 9600, 19200, 57600, 115200 in x1 mode, and 8 times these rates in x8 mode i.e. up to 921600 baud.
Supported by standard drivers in DOS*, Windows95, 98, 98SE, Me, 2000, XP, Ce, PocketPC & Linux.
For more information about Linux support please click here !
Card comes with Elan's Card Center Pro software that installs INF scripts and sample code Automatic O.S. recognition and configuration.
Hot swappable CF+ compliant TypeI design.
Low power consumption: Typical 35mA at 5V, with support for reduced power sleep mode (depends on O.S.).
Will also work at 3.3V for hosts that cannot supply 5V.
Supplied with 300mm Type46 cable.
Connector latches into CF Card for security. DB9 Male with female screwlocks for attachment to terminal equipment.
Also available with robust direct cable termination instead of Type46 cable, product code CF428R. MOQ may apply.
*DOS support requires Card and Socket services, e.g. CardWare from APSoft see http://www.tssc.de
| 
